Page 1 of 1
Painting the house...
Posted: Tue Jul 07, 2009 6:47 pm
by Razorclaw
We had decided to paint our house, so i wanted to make something new for my room. Thus, i decided to paint a Decepticon insignia. It took me 8 hours (
) to finish it.
Posted: Tue Jul 07, 2009 6:50 pm
by Dinobot
Geez 8 hours?! That bites but it looks so awesome! I love that color.
Posted: Tue Jul 07, 2009 6:58 pm
by Razorclaw
Thanks.
At first i made it black but it didn't turn out as i expected.
But a few shadings with blue did the trick.
To find the correct dimensions was a real pain; and still, its not 100% accurate but i got really tired and i had to finish it.
Posted: Tue Jul 07, 2009 8:56 pm
by Banzai-Tron
Haha. This is EXACTLY why I keep an old school style overhead transparency projector lying around the garage! It'd cut this project down to 2 hours, tops. Probably only 1.
Posted: Tue Jul 07, 2009 11:24 pm
by Time Traveller
do you have the capability to print transparencies, or would you just draw it?
Looks cool, Razorclaw, but you know deep down it's the wrong faction.
Posted: Wed Jul 08, 2009 5:06 am
by Banzai-Tron
Generally, you can print directly onto transparency paper with either an inkjet or bubblejet printer. If you have a laser jet printer, I believe you need to buy a special type of transparency paper.
I use inkjet with my transparencies, and it works well... though you need to watch out for smearing. I also had to try a couple different printers to find one that didn't smear it while it printed.
EDIT: And of course, even if you *couldn't* print directly on them... there's always tracing!
EDIT2: I just looked. They now make a transparency film that can be used with ANY printer. A bit pricy at about 75cents a sheet though. (Box of 50=$36.00)
Posted: Wed Jul 08, 2009 5:11 am
by LD2062
You need special transparencies for inkjets too. Thats why it was smearing. They are usually kind of expensive. But Walmart has packs of 10 for like $5-$10.
Edit: Can you post a link to those transparencies?
If you don't want to bother you with the whole issue. Simply have a photo file, or normal print, up to an office store or other place with printing services. It should only cost about $2 for a single page.
Posted: Wed Jul 08, 2009 6:28 am
by Minerva
Looks very cool! Nice job, Razorclaw!
Are you planning on making an Autobot insignia too?
Posted: Wed Jul 08, 2009 10:48 am
by Ramjet
Looks cool! You should have done it the size of the whole wall, though!
Posted: Wed Jul 08, 2009 12:34 pm
by Commander Megatron
Time Traveller wrote:Looks cool, Razorclaw, but you know deep down it's the wrong faction.
Ignore him!!! It looks awesome Razorclaw, a fantastic job well done. YOur leader approves whole heartedly.
Posted: Wed Jul 08, 2009 12:50 pm
by Rumble
Nice work Razorclaw!
Rumble.
Posted: Wed Jul 08, 2009 4:59 pm
by Razorclaw
Thanks everyone.
It must be close to 19 inches high.
@ CM: Don't worry, i can't be controlled...
P.S.: I knew you'd like it!
@Minerva: Well, no way!
I wouldn't do it again, especially for an insignia that is not composed by straight lines only!
@Ramjet: Yeah, sure...i'd still have been there calculating and painting!