Page 1 of 2
Shame!!!!!
Posted: Sat Oct 10, 2009 9:34 am
by Hot Rod
Shame we can't have all the Coneheads in this mold........THAT WOULD BE NICE!!!!!!
http://www.youtube.com/watch?v=YBBuB7W8X1k
Posted: Sat Oct 10, 2009 9:52 am
by Deszaras
No its a shame that the other two coneheads colour schemes were not also put to good use to accompany ramjet. {Using the voyager 07' movie starscream mold} (Thrust's name and colour scheme has already been wasted on a pointless Breakaway remold.}
I personally dislike that mold and have disliked it since it was first shown.
Posted: Sat Oct 10, 2009 9:54 am
by Hot Rod
Deszaras wrote:No its a shame that the other two coneheads colour schemes were not also put to good use to accompany ramjet. {Using the voyager 07' movie starscream mold} (Thrust's name and colour scheme has already been wasted on a pointless Breakaway remold.}
I personally dislike that mold and have disliked it since it was first shown.
Which mold?????
Posted: Sat Oct 10, 2009 9:56 am
by Deszaras
Hot Rod wrote:Deszaras wrote:No its a shame that the other two coneheads colour schemes were not also put to good use to accompany ramjet. {Using the voyager 07' movie starscream mold} (Thrust's name and colour scheme has already been wasted on a pointless Breakaway remold.}
I personally dislike that mold and have disliked it since it was first shown.
Which mold?????
The dirge one in that vid. {Also Breakaway's mold isn't much to shout about}
[I really like the old 07' movie screamer mold. I'll have to hunt down a couple of 'em and do some customs to finish off the set.]
Posted: Sat Oct 10, 2009 10:02 am
by Rumble
Deszaras wrote:Hot Rod wrote:Deszaras wrote:No its a shame that the other two coneheads colour schemes were not also put to good use to accompany ramjet. {Using the voyager 07' movie starscream mold} (Thrust's name and colour scheme has already been wasted on a pointless Breakaway remold.}
I personally dislike that mold and have disliked it since it was first shown.
Which mold?????
The dirge one in that vid. {Also Breakaway's mold isn't much to shout about}
[I really like the old 07' movie screamer mold. I'll have to hunt down a couple of 'em and do some customs to finish off the set.]
Might as well wait Des, they are bound to be pushed out for the next movie.
Rumble.
Posted: Sat Oct 10, 2009 10:04 am
by Deszaras
Rumble wrote:
Might as well wait Des, they are bound to be pushed out for the next movie.
Rumble.
Probably using the newer ROTF Voyager starscream mold. Which I dislike
Posted: Sat Oct 10, 2009 10:06 am
by Hot Rod
The 07 Starscream mold is one of the worst there is he has no real hands and far to much bulk under the jet..............the harrier mold is great it looks like the real deal no extra bulk that shouldn't be there and a really good fresh new look.
If Starscream's what you want the ROTF mold is far superior to the 07 mold.
Posted: Sat Oct 10, 2009 10:13 am
by Deszaras
Hot Rod wrote:The 07 Starscream mold is one of the worst there is he has no real hands and far to much bulk under the jet..............the harrier mold is great it looks like the real deal no extra bulk that shouldn't be there and a really good fresh new look.
If Starscream's what you want the ROTF mold is far superior to the 07 mold.
that is your opinion. My view of the ROTF screamer is that he is overly flimsy and is made of very thin plastic.
I like the bulk of the 07' movie screamer and there's not really any major assembly flaws in the mold that I am aware of.
Posted: Sat Oct 10, 2009 10:19 am
by Hot Rod
The plastic is no different tro that of the 07 mold plus there are no flaws in the mold either.
Posted: Sat Oct 10, 2009 10:22 am
by Deszaras
Hot Rod wrote:The plastic is no different tro that of the 07 mold plus there are no flaws in the mold either.
Read my review on the mold. I encountered a few serious problems after I had the figure for a week. Down to personal preference I suppose in the end.
I am curious as to what the leader class ROTF starscream will be like, but I will not buy the ROTF voyager one again due to the problems I had with the first one of them I bought.
Posted: Sat Oct 10, 2009 10:26 am
by Hot Rod
Deszaras wrote:Hot Rod wrote:The plastic is no different tro that of the 07 mold plus there are no flaws in the mold either.
Read my review on the mold. I encountered a few serious problems after I had the figure for a week. Down to personal preference I suppose in the end.
I am curious as to what the leader class ROTF starscream will be like, but I will not buy the ROTF voyager one again due to the problems I had with the first one of them I bought.
I don't need to read your review i have both molds.........No problems.
Posted: Sat Oct 10, 2009 10:35 am
by Hot Rod
Also the tabs that hold the wings in place are fine on mine he was even fell off a shelf onto a hardwood floor and survived without a scratch, how's that for durable, pretty good i'd say.
Posted: Sat Oct 10, 2009 11:03 am
by Perceptor
Old school rocks hard.
Posted: Sat Oct 10, 2009 5:46 pm
by Jazz
Thats a nice looking Deluxe class... Thats all im saying.
Posted: Sat Oct 10, 2009 10:53 pm
by Ultra Magnus
Folks, we all have differences of opinions, but lets to to remain friendly in here.
Thanks,
UM
-TFL Admin
Posted: Sun Oct 11, 2009 7:42 pm
by captainamerica
UM, I reeeeeeeally like your sig. A TF doing a prowrestling move is powerfully awesome. I certainly hope he went for the pin after landing that enziguri.
Posted: Sun Oct 11, 2009 8:51 pm
by The Last Autobot
Okay. I like that mold. Sorry.
Posted: Mon Oct 12, 2009 4:48 pm
by NUCKATRON
Man I CANT WAIT to get that new Dirge!!! When will it be released? I'm going to get a couple extra to re-paint into Thrust and Ramjet for sure!
Posted: Tue Oct 13, 2009 1:28 pm
by Hot Rod
Probably sometime next year i recon!!!
Posted: Wed Oct 14, 2009 1:00 pm
by The Last Autobot
That is too long of a wait to get that toy...